On this page down the page you'll find additional outstanding additional info involving How to Install a Bathtub.
Installing a bath tub isn't precisely rocket science, yet it does require strong plumbing, woodworking, and often, tiling abilities. Changing an old tub with a brand-new one is likewise a moderately difficult task. If the old bathtub is easily available, the task can relocate rapidly; if you have to open up a wall to get rid of the old tub and also place the brand-new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will require an assistant to vacate the old bathtub and set in the brand-new one. Make certain you have actually certified yourself for the job and fit attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is much better to consider employing one prior to you start. Possibilities are you may require a specialist plumber to make tube connections.
This short article will certainly aid you set up a new tub in your washroom if you have currently gotten a new bathtub and also don't require to alter the arrangement of your previous water system pipelines.
Your tools and material checklist ought to make up the following:
Preparing for the Setup
Firstly, the supporting frame supplied with the bath must be fitted (if needed) according to the producer's directions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the tap features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets unit to avoid stress on the tub.
Fit the versatile faucet adapters to the bottom of the two faucets using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you use all of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently be ready to be suited its last placement.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is detach the water. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The process of eliminating the existing taps can be rather troublesome as a result of the limited access that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipelines. As soon as the supply pipes have actually been removed, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from turning throughout this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any kind of old securing compound.
Prior to going on to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Making use of both wood boards under its feet, put the bath tub in the called for setting. The wood boards are handy in evenly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four small points.
The next objective is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and readjusting the feet on the tub until the spirit level checks out degree.
To mount faucets, fit all-time low of the furthest adaptable tap port to the suitable supply pipeline by making a compression sign up with; after that do the very same for the other faucet.
Turn on the water and also examine all joints and brand-new pipework for leaks and also tighten them if required. Fill the bathtub and likewise examine the overflow electrical outlet and also the typical electrical outlet for leakages.
Finally, take care of the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and securing around the bath tub needs to wait till the bath tub has been used a minimum of when as this will settle it into its last setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin making certain that the washers are in location between the tap as well as the sink. Protect the faucet in position with the maker offered backnut. When the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical faucet adapters. The former kind needs to be linked to the faucet finishes first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to split a stiff seal, causing the water to permeate the wall in between the bath as well as the tiling, leading to issues with dampness and also feasible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, as well as can securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to securing, to enable the motion experienced when the tub remains in usage. The sealer can break rather early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been guided to that article on How to Install a Bathtub Yourself through an associate on another site. Those who enjoyed reading our article plz make sure you remember to share it. I treasure reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Ensure plumbing safety.